Cary Audio Design Stereo Amplifier Xciter User Manual

Xciter Amplifier  
Integrated Stereo Vacuum Tube Amplier  
NOTE: Before installing your new component, please read this manual carefully  
as it will inform you of the product specications, proper installation and correct  
operating procedures for your unit. Also included in this manual are guidelines  
on how to service and care for your new Cary Audio Design product.  
 
IMPORTANT SAFETY INSTRUCTIONS  
WARNING: To reduce the risk of fire or electric shock, do  
not expose this appliance to rain or moisture. The lightning  
flash with arrowhead symbol within an equilateral triangle is  
intended to alert the user to the presence of un-insulated  
dangerous voltage within the product’s enclosure that may  
be of sufficient magnitude to constitute a risk of electric  
shock to persons.  
CAUTION: To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside.  
Please refer to qualified personnel for service.  
ALERT: The exclamation point within an equilateral triangle is intended to alert the user of the presence of important  
operating and maintenance (servicing) instructions in the literature accompanying the component.  
1. READ ALL INSTRUCTIONS: All the safety and operating instructions of your Cary Audio equipment should be read  
before power is applied to the equipment.  
2. RETAIN OWNER'S MANUAL: These safety and operating instructions should be retained for future reference.  
3. HEED WARNING: All warnings on the unit and in the operating instructions should be adhered to.  
4. FOLLOW INSTRUCTIONS: All operating and use instructions should be followed.  
5. CLEANING: Unplug the unit from the wall outlet before cleaning. The unit should be cleaned only as recommended  
by the manufacturer.  
6. ATTACHMENTS: Do not use attachments not recommended by the unit manufacturer as they may cause hazards.  
7. WATER AND MOISTURE: Do not use the unit near water - for example, near a bath tub, wash bowl, kitchen sink,  
or laundry tub; in a wet basement; or near a swimming pool.  
8. ACCESSORIES: Do not place the unit on an unstable cart, stand, tripod, bracket, or table. The unit may fall,  
causing serious injury to a child, an adult, or damage to the unit. Mounting of the unit should follow the  
manufacturer's instructions and should use a mounting accessory recommended by the manufacturer.  
9. VENTILATION: Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the  
unit and to protect it from overheating. These openings must not be blocked or covered. The top or bottom panel  
openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. The unit should  
not be installed in a built-in location such as a bookcase or rack unless proper ventilation is provided. There should  
be free space of at least 6 inches (16cm) above the unit and an opening behind the unit.  
10. GROUNDING OR POLARIZATION: The unit may be equipped with a polarized alternating current line plug (a  
plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety  
feature. If you cannot insert the plug fully into the outlet, try reversing the plug. If the plug should fail to fit, contact  
a licensed electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.  
11. POWER SOURCES: The unit should be operated only from the type of power source indicated on the marking  
label. If you are not sure of the type of power supplied to your home, consult your unit dealer or local power  
company.  
12. POWER CORD PROTECTION: Power supply cords should be routed so that they are unlikely to be walked on or  
pinched by items placed on or against them. Pay close attention to cords where they enter a plug, or a convenience  
receptacle, and the point where they exit from the unit.  
13. OUTDOOR ANTENNA GROUNDING: If an outside antenna or cable system is connected to the unit, be sure the  
antenna or cable system is grounded so as to provide protection against voltage surges and built-up static charges.  
Article 810 of the National Electrical Code, NSI/NFPA 70, provides information regarding proper grounding of the  
mast and supporting structure, grounding of the lead-in wire to an Antenna-discharge unit, size of grounding  
conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the  
grounding electrode.  
2
 
IMPORTANT SAFETY INSTRUCTIONS  
14. LIGHTNING: For added protection for the unit during a lightning storm, or when it is left unattended and unused  
for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent  
damage to the unit due to lightning and power line surges.  
15. POWER LINES: An outside antenna system should not be located in the vicinity of overhead power lines or other  
electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside  
antenna system, take extreme care to keep from touching such power lines or circuits as contact with them might be  
fatal.  
16. OVERLOADING: Do not overload wall outlets, extension cords, or integral convenience receptacles as this can  
result in a risk of fire or electric shock.  
17. OBJECT AND LIQUID ENTRY: Never push objects of any kind into the unit through openings as they may touch  
dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind  
on the unit.  
18. SERVICING: Do not attempt to service the unit yourself as opening or removing covers may expose you to  
dangerous voltage or other hazards. Refer all servicing to qualified service personnel.  
19. REPLACEMENT PARTS: When replacement parts are required, be sure the service technician has used  
replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized  
substitutions may result in fire, electric shock or other hazards.  
20. SAFETY CHECK: Upon completion of any service or repairs to the unit, ask the service technician to perform safety  
checks to determine that the unit is in proper operating condition.  
21. WALL OR CEILING MOUNTING: The unit should be mounted to a wall or ceiling only as recommended by the  
manufacturer.  
22. HEAT: The unit should be situated away from heat sources such as radiators, heat registers, stoves, or other units  
(including amplifiers) that produce heat.  
23. IMPORTANT SAFETY NOTE: Before connecting a new component to your audio or home theater system it is  
always good practice to make certain that all components are turned off, and preferably unplugged from their AC  
power source. Many modern electronics products feature automatic turn-on circuits that may be activated during an  
installation, causing the potential for damage to electronic components and/or speakers. Such damage is not  
covered by product warranties and Cary Audio specifically disclaims responsibility for any such damage.  
Power Cord: The removable power cord that is shipped with the player is specifically designed to be used with this  
product. Other AC cords may be used, so consult your dealer for advice on AC power cords and high quality wire in  
your system.  
AC Fuse: The fuse is located inside the chassis and is not user serviceable. If power does not  
come on, contact your authorized service representative.  
Wiring: Cables that run inside of walls should have the appropriate markings to indicate  
compliance with, and listing by the UL, CSA or other standards required by the UL, CSA, NEC or your local building  
code. Questions about cables inside of walls should be referred to a qualified custom installer, or a licensed  
electrician or low-voltage contractor.  
Do Not Open the Cabinet: There are no user serviceable components inside this product. Opening the cabinet  
may present a shock hazard, and any modification to the product will void your warranty. If water or any metal  
object, such as a paper clip, coin, or staple accidentally falls inside the unit, disconnect it from the AC power source  
immediately and contact Cary Audio for further instructions.  
24. RECORDING COPYRIGHT: Recording of copyrighted material for other than personal use is illegal without  
permission of the copyright holder.  
25. NOTE TO CATV SYSTEM INSTALLER: This reminder is provided to call the CATV system installer's attention to  
article 820-40 of the NEC, ANSI/NFPA 70, which provides guidelines for proper grounding and, in particular, specifies  
that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry  
as practical.  
3
 
IMPORTANT SAFETY INSTRUCTIONS  
26. FCC INFORMATION FOR USER:  
CAUTION: ANY changes or modifications not expressly approved by the party responsible  
for compliance could void the user's authority to operate the equipment.  
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to  
Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation.  
This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with  
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that  
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to  
correct the interference by one or more of the following measures:  
- Reorient or relocate the receiving antenna.  
- Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from where the receiver is connected.  
27. OUTDOOR ANTENNA INSTALLATION/SAFE ANTENNA AND CABLE  
CONNECTION: If an outside antenna or cable system is connected to  
the equipment, be sure the antenna or cable system is grounded so as to  
provide protection against built up static charges and voltage surges,  
Section 810 of the national Electrical Code, ANSI/NFP A70 (in Canada,  
part 1 of the Canadian Electrical Code) provides information with respect  
to proper grounding of the mast and supporting structure, grounding of  
the lead-in wire to an antenna discharge unit, size of grounding  
conductors, location of antenna discharge unit, connection to grounding  
electrodes and requirements for the grounding electrode.  
Keep Antenna Clear of High Voltage Power Lines or Circuits  
An outside antenna system should be located well away from power lines, electric light or power circuits and where  
it will never come into contact with these power sources if it should happen to fall. When installing an outside  
antenna, extreme care should be taken to avoid touching power lines, circuits or other power sources as this could  
be fatal. Because of the hazards involved, antenna installation should be left to a professional.  
4
 
WELCOME  
THANK YOU  
Dear Cary Audio Customer:  
I am so pleased and excited about the new Cary Audio Design Xciter, stereo vacuum tube  
integrated amplifier. I have spent countless hours designing and refining this very special  
vacuum tube amplifier. The Xciter started life in April of 2008 as a companion to a new digital to  
analog USB converter I was designing. I had recently discovered the merits of computer full  
bandwidth audio. In fact I found my self watching DVD’s on the computer and using the new  
Xciter amplifier and a pair of C4 Dynaudio loudspeakers in my listening room. In my lab I found  
myself listening to the Xciter amplifier with the amazing Grado GS-1000 headphones. What a  
neat combination. I thought this combo had merit and began percolating the final designs in my  
in my head. Then to the drawing board.  
In October, six months after the initial prototype I had the cosmetic package complete. I needed  
to have these new babies on display at the January 2009 CES Show.  
Well it is now December of 2008 and I am once again an excited “design-boy” watching the new  
Xciter integrated amplifiers go down the Apex, North Carolina, Cary “toy” shop production line.  
The companion Xciter DAC will come into production in February of 2009. I can now answer the  
question: “How does it sound?” “Amazing, I love it, I love it!!!!!!”  
Enjoy the music in your home, or office with your new Xciter integrated amplifier and thank you  
for your support.  
God Bless you and your family.  
Dennis and the Cary Audio Team  
WARNING  
Electrical hazard! Misuse or failure to follow instructions properly may result in  
personal injury or death!  
CAUTION  
No risk or personal injury; however, misuse or failure to follow instructions may result  
in damage to equipment.  
NOTE  
No risk of personal injury or equipment damage; however, misuse or failure to follow  
instructions may prevent proper performance of the equipment.  
5
 
WELCOME  
PRODUCT FEATURES  
The stereo vacuum tube power amplifier has a great history at Cary Audio Design. The superb  
lineage of CAD power amplifiers and integrated amplifiers have consistently garnered fantastic  
reviews for stable power output, incredible value for the money and sound quality along with  
‘Best Buy’ and ‘Class A’ ratings from magazines and reviewers worldwide. Building on this storied  
legacy, we are releasing the CAD Xciter Integrated stereo vacuum tube power amplifier. This  
innovative stereo power amplifier was conceived to be a small desktop integrated amp to be  
companion to the new CAD Xciter Digitial to Analog Converter. In the Cary tradition, it features  
a gorgeous cabinet and has a subtle touch of translucent blue LED back lighting to complement  
the natural beauty of the vacuum tubes. Although it may be small in physical size it is imbued  
with the full spirit of Cary Audio. Its 5 watts per channel in class A triode mode plays much  
bigger than you might expect and its sublime musicality is just what you would expect from Cary  
Audio. For headphone lovers, a standard ¼ inch diameter, 3 circuit output jack is conveniently  
located on the front panel to pipe the music to your favorite set of cans. The circuitry is  
optimized to provide a good match for all high quality headphones. A front panel switch allows  
the user to select between the speakers or headphones. Additional features are the subwoofer  
outputs - one for each channel, and the motorized remote control function for adjusting listening  
level and mute. You will absolutely enjoy listening to this lovely amplifier – it truly is an Xciter!  
The input circuit is a single-ended design with three (3) switched RCA stereo inputs per channel.  
The vacuum tubes in each channel consist of one (1) 12AX7A (dual triode) for the input gain and  
for the driver stage and two (2) 6L6GC output power tubes. The filaments of the 12AX7A stages  
are direct heated with filtered and regulated 12 VDC for lower noise performance. The first  
section of 12AX7A provides the low level preamp gain stage and the second section provides the  
phase inverter and differential driver stage. Both sections of the 12AX7A are operating in Class A  
with minimal feedback. The 6L6GC output tubes are configured as triodes and operated in a class  
A push-pull configuration and are continuously auto biased through cathode auto biasing  
circuitry. The laminate output transformers are customized to match the output circuit  
requirements and have a signal handling capacity well beyond the amplifiers demands to avoid  
any problems with linearity and saturation. Five-way Gold plated speaker binding posts provide  
reliable connection to your speakers. Frequency response at full rated output power is from 17  
Hz to 23 kHz with less than 2% total harmonic distortion.  
The circuitry for the entire amp is designed into a high-grade two-layer printed circuit board with  
extensive ground planes and heavy copper circuit traces on the power bus circuitry. Shielded  
coaxial cable is used for critical signal path component interfaces. This design approach imparts  
an extremely clean layout and a very high performance level. A toroidal power transformer  
provides the foundation for a compact, yet high efficiency power supply. The power supply  
features seven (7) 100 micro farad low impedance low profile electrolytic capacitors which yields  
an abundant total of 700 micro farads of energy storage and provides an excellent dynamic  
performance capability. The high voltage power bus is further enhanced with a power choke in a  
pi-L configuration for additional filtering to the preamp stage and with two (2) high speed .22  
microfarad Kimber Kap polystyrene by-pass capacitors to further enhance the superb transient  
response characteristics under demanding musical passages.  
The CAD Xciter integrated Stereo Amplifier is the perfect match for the CAD Xciter Digital  
Analog Converter. Together, the companion Xciter tandem will beautify your office or listening  
room and deliver a no compromise musical listening experience in a small package.  
Let the Xcitement rock!  
6
 
WELCOME  
UNPACKING AND INSTALLATION  
This section describes the unpacking and installation procedures for your new component.  
Unpacking  
All Cary Audio Design shipping cartons have been specially designed to protect their contents and  
special care has been taken to prevent damage under normal shipping conditions. Mishandling  
should be evident upon inspection of the shipping container. If shipping damage is found after  
visual inspection, take care not to destroy the evidence. If necessary, document the damage with  
photographs and contact the transport carrier immediately.  
Carefully remove your new component from its packing carton and examine it closely for signs of  
shipping damage. We strongly recommend saving all original packing cartons to protect your  
component from damage should you wish to store it or ship it at a later date.  
In the Box  
When unpacking your CAD Xciter power amplifier, make sure the following accessories are  
included. You should find the following items:  
Power Cable  
Owner’s Manual  
Warranty Card  
Spare Fuses  
Warranty Card  
If you are the original purchaser of this unit and you purchased it in the United States, you  
should fill out the enclosed warranty registration card and return it to Cary Audio Design within  
15 days of your purchase. Cary Audio Design also suggests that you keep your original packing  
cartons in case you ever need to ship the unit when moving to a new home. Warranty  
restrictions apply. Consult the warranty section of this manual for details. Please be certain to  
keep a copy of the original sales receipt from your Authorized Cary Audio Design dealer to  
validate the warranty if ever needed.  
7
 
SPECIFICATIONS  
Operating the CAD Xciter is a simple procedure. It is designed for long-term stability in virtually  
any home operating environment. However, if the unit is operated outside the parameters  
outlined in this owner's manual, damage may result. Please read this manual carefully before  
putting your new CAD Xciter amplifier into operation.  
The following section describes the CAD Xciter amplifiers’ basic specifications. The specifications  
are subject to change without notice or obligation.  
...........................................................................................................................................................................  
Circuit Type  
Class A triode push-pull amplifier, Auto-Bias Triode mode  
operation  
...........................................................................................................................................................................  
Power Output  
5 Watts per channel into 8 ohm load  
...........................................................................................................................................................................  
Line Inputs  
3 selectable inputs per channel - RCA single-ended  
(Gold Plated)  
...........................................................................................................................................................................  
Sub-Woofer Outputs  
Sub-woofer Out - RCA single-ended - one for each channel  
(Gold Plated)  
...........................................................................................................................................................................  
Headphone Output  
4 - 600 ohm compatible - 1/4"diameter, 3 circuit jack  
...........................................................................................................................................................................  
Noise and Hum  
-80 dB below rated output  
...........................................................................................................................................................................  
Input Impedance  
100K - RCA Unbalanced  
...........................................................................................................................................................................  
Frequency Response  
17 Hz - 25 KHz flat @ 1 watt  
...........................................................................................................................................................................  
Tubes  
2 - 12AX7A input gain stage/ driver stage  
4 - 6L6GC output tubes  
...........................................................................................................................................................................  
Power Transformer  
High Efficiency Toroidal for both High Voltage and Low Voltage  
Requirements  
...........................................................................................................................................................................  
Output Transformer(s)  
Custom laminate – 15 watt rating  
...........................................................................................................................................................................  
Resistors  
1% precision metal film  
...........................................................................................................................................................................  
Capacitors  
Polystyrene, Film, and Foil  
...........................................................................................................................................................................  
Power Supply Capacitors  
7 x 100 Micro Farad @450VDC (Low Impedance Electrolytic),  
2 x 0.22 Micro Farad @600VDC (Polystyrene Kimber Kaps)  
...........................................................................................................................................................................  
Speaker Posts  
Gold plated copper, 5-way binding  
...........................................................................................................................................................................  
Wiring  
Printed Circuit Board and custom point to cabling  
(all low level signal cables are shielded coaxial)  
...........................................................................................................................................................................  
AC Cord  
3 Conductor Shielded, Detachable  
...........................................................................................................................................................................  
AC Power Requirements  
117 VAC @ 50/60 Hz  
234 VAC @ 50/60 Hz  
...........................................................................................................................................................................  
Power Consumption  
80 Watts idle, 85 Watts Full Power Output  
8
 
SPECIFICATIONS  
Warm-Up Time  
3 minutes  
...........................................................................................................................................................................  
Break-In Time  
100 hours of playing time  
...........................................................................................................................................................................  
Finish  
Black Powder Coat Gloss and Matte, silver anodized aluminum  
faceplate standard (black optional)  
...........................................................................................................................................................................  
Weight  
16.5 lbs  
...........................................................................................................................................................................  
Dimensions  
5 7/8" H x 11" W x 13" D  
...........................................................................................................................................................................  
9
 
CONTROLS AND DISPLAYS  
FRONT PANEL  
1. AC POWER SWITCH  
Press the “1” at the top of the rocker switch to turn the power ON.  
Press the “0” at the bottom of the rocker switch to turn the power OFF.  
2. SOURCE SELECTOR SWITCH  
Rotate to select one of 3 inputs for each channel  
3. MUTE INDICATOR LED  
Indicates mute function is activated when illuminated  
Press remote control “Mute” button to activate Mute, Press “Mute” button again to  
deactivate the Mute function  
4. LISTENING LEVEL CONTROL  
Rotate to adjust the listening (or volume) level of the amplifier output  
Press remote control Volume “- ” or +” buttons to adjust listening level  
5. INFRARED (IR) SENSOR  
Sensor receives signals from remote control hand held sending unit  
Keep sensor free from obstructions, the sensor will not receive the signals from the  
hand held unit if obstructed  
6. HEADPHONE SELECTOR SWITCH  
Rotate to “On” position to select output to the headphones  
Rotate to “Off ” position to select output to the speakers (the headphone output is  
disabled when switch is in the “Off ” position)  
7. HEADPHONE JACK  
Standard ¼” diameter 3 circuit headphone access jack  
Use dynamic 30 – 300 ohm impedance headphones  
8. HEADPHONE INDICATOR LED  
Indicates headphone function is activated when illuminated  
10  
 
CONTROLS AND DISPLAYS  
REAR PANEL  
1. RIGHT CHANNEL INPUT – NUMBER 1  
2. RIGHT CHANNEL INPUT – NUMBER 2  
3. RIGHT CHANNEL INPUT – NUMBER 3  
4. RIGHT CHANNEL SUBWOOFER OUTPUT  
5. LEFT CHANNEL SUBWOOFER OUTPUT  
6. RIGHT CHANNEL INPUT – NUMBER 3  
7. RIGHT CHANNEL INPUT – NUMBER 2  
8. RIGHT CHANNEL INPUT – NUMBER 1  
9. LEFT CHANNEL SPEAKER OUTPUT – NEGATIVE LEAD  
10. LEFT CHANNEL SPEAKER OUTPUT – POSITIVE LEAD  
11. AC POWER CORD JACK  
12. AC POWER FUSE PANEL  
13. LEFT CHANNEL SPEAKER OUTPUT – POSITIVE LEAD  
14. LEFT CHANNEL SPEAKER OUTPUT – NEGATIVE LEAD  
11  
 
CONTROLS AND DISPLAYS  
TOP PANEL  
The following illustration shows the tube placements on the CAD Xciter.  
12  
 
OPERATION  
Your new CAD Xciter integrated amplifier is ready for operation after the AC power, speaker,  
and interconnect cables and the vacuum tubes have been installed into their proper sockets.  
Refer to the labeling on the chassis for placement and proper tube installation. Since the  
amplifier circuitry is completely auto-biasing, no biasing adjustments are required – just plug and  
play!  
AC POWER REQUIREMENTS  
The CAD Xciter is designed to work from house current AC mains. The design voltage is 120  
Volts AC at 50/60 Hz (Foreign units 240 Volts AC at 50/60 Hz). Plug the provided AC power cable  
into the AC Power jack on the rear panel of the unit.  
SOURCE INPUTS  
The CAD Xciter accepts 3 unbalanced stereo inputs via the RCA jacks on the rear panel.  
Nominal input impedance is 100K Ohm and provides compatibility with common sources such as  
CD/DVD players, DAC, Cinema, Tuner, and Tape. A shielded high quality interconnect cable is  
important to reduce chances for hum or interference. Ask your Authorized Cary Audio Design  
dealer for advice.  
SUBWOOFER OUTPUTS  
The CAD Xciter provides buffered low level outputs of the selected stereo source input via the  
RCA jacks on the rear panel suitable for driving the low level input of amplified subwoofers. A  
shielded high quality interconnect cable is important to reduce chances for hum or interference.  
Ask your Authorized Cary Audio Design dealer for advice.  
SPEAKER BINDING POSTS  
The CAD Xciter will drive loudspeaker loads from as low as 4 ohms to a high of 16 ohms  
without any adjustments. Please remember to keep the proper phase on each channel when  
connecting the loudspeaker cables. Red is the positive and black is the negative lead. The  
positive binding post (on both left and right channels) is located closest to the middle of the  
chassis. Check your speaker cables periodically to make sure the connections are tight.  
POWER ON / OFF SWITCH  
The AC Power rocker switch for power on - power off is located in the lower left-hand corner of  
the front panel. The CAD Xciter becomes fully operational once the AC Power cord is plugged  
into the unit and into the wall AC outlet the Power On/Off switch is turned On. Push the “1” at  
the top of the switch to turn the unit on. You will notice that blue back lighting behind the  
Listening Level control on the front panel will illuminate. The vacuum tubes will light as well. Blue  
LEDs will also illuminate the base of each 12AX7A tube. The unit is powered down (turned off)  
simply by pushing the “0” at the bottom of the power switch. AC power is then removed from  
the power supply in the CAD Xciter.  
13  
 
OPERATION  
SOURCE SELECTOR  
The Source Selector switch, located on the front panel, allows the selection of one of three input  
stereo source selections connected to the RCA input jacks on the rear panel. Simply rotate the  
knob of the selector switch to the desired input source.  
LISTENING LEVEL  
The Listening Level control, a potentiometer located in middle of the front panel, allows the  
adjustment of the listening level (or output volume). Simply rotate the knob of the control to  
either increase or reduce the listening level. Alternatively, the listening level can be remotely  
controlled. The Remote Control Operation sections details the use of the hand held remote for  
this function.  
REMOTE CONTROL  
The hand held remote control allows the convenient adjustment of both listening level and the  
mute function. Point the hand held remote toward the amplifier front panel and press the remote  
control Volume “-” button to reduce listening level or press remote control Volume “+” button to  
increase listening level. The listening level potentiometer is motorized and you will see the large  
Listening Level control knob physically move as you adjust the listening level.  
Point the hand held remote toward the amplifier front panel and press the remote control “Mute”  
button to activate Mute. Press “Mute” button again to deactivate the Mute function. A red LED  
indicator lamp located between the Source Selector switch and the Listening Level control will  
illuminate when the Mute function is On. The LED will go off when the Mute function is Off.  
The infrared (IR) sensor is located on the front panel between the Listening Level control and the  
Headphone On/Off switch. The IR sensor must be free of obstructions in order to receive the  
signals from the hand held remote. The remote must be pointed to the front panel of the  
amplifier to function correctly.  
HEADPHONE FUNCTION  
The Headphone On/Off switch, located on the front panel, allows the output of the amplifier to  
be switched from the speakers to headphone jack when the switch is rotated to the “On”  
position. When the switch is set to the “Off” position the output of the amplifier is switched only  
to the speaker jacks. The headphone jack is not functional while the speakers are operating and  
the speaker jacks are not functioning when the headphone jack is active. A blue LED indicator  
lamp located just above the Headphone Jack will illuminate when the Headphone Jack is On. The  
LED will go off when the Headphone function is Off.  
The 3 circuit headphone jack accepts a ¼” diameter stereo plug. Be sure to plug your  
headphone plug securely into the headphone jack. The CAD Xciter is capable of driving nearly  
any dynamic headphone set to very high levels. The Listening Level control should be turned to a  
low setting prior to listening with headphones to avoid potential exposure to excessively loud  
sound levels. The listening level can then be adjusted to a comfortable setting.  
14  
 
OPERATION  
BREAK-IN PERIOD  
The tubes, capacitors and output transformers take approximately 100 hours use to settle in for  
peak performance. The CAD Xciter will sound good right out of the box but it will improve  
within a short time. After the first 50-100 hours you will notice increased depth and tighter bass.  
This break-in period is characteristic with quality vacuum tube audio amplifiers.  
15  
 
SERVICE AND CARE  
TUBE REPLACEMENT  
If it becomes necessary to replace the tubes in the amplifier, a matched set of output tubes of  
the same name brand should be used. A new tube kit is available from Cary Audio. You should  
get years of service from the rugged 6L6GC output tubes. The input and driver 12AX7A tubes can  
last even longer. Other output tubes may be used in the CAD Xciter amplifier include: 6V6,  
5881, or EL-34 tubes are all acceptable for use in the output stage of the CAD XCITER. The  
output tube circuitry will automatically set the proper bias level for the output tubes in use.  
The unit should be turned off and the tubes allowed a cool down period prior to replacement.  
The tubes operate at high temperatures and should not be touched while hot. Ask your  
Authorized Cary Audio Design dealer for advice on tube selection and replacement.  
AC POWER FUSE REPLACEMENT  
Never replace fuse with any other value than a three (3) amp slow blow fuse, 250 Volt for a unit  
configured to operate at 120 Volts AC. Never use any other value than a two (2) amp slow blow  
fuse, 250 Volt for a unit configured to operate at 240 Volts AC. The AC Power Cord must be  
unplugged from the AC Power jack on the back of the unit prior to replacing the fuse. The fuse  
panel can then be removed from the unit by inserting the tip of a small screwdriver into the small  
tab at top edge of the fuse panel and then pushing the panel out from the jack. The fuse is the  
5mm x20mm type and fits into the clip inside the fuse panel. After the panel is extracted remove  
the old fuse from the mounting clip and install the new fuse into the clip. Carefully slide the fuse  
panel back into the AC jack assembly after inserting the new fuse. Set the unit Power On/Off  
switch to the Off position and plug the AC Power cord back into the AC Power jack. Then set the  
Power On/Off switch to the On position and verify proper operation. Ask your Authorized Cary  
Audio Design dealer for advice if the fuse repeatedly blows.  
CARE AND CLEANING  
The cabinet housing and front panel of the CAD Xciter may be cleaned with a soft cloth and  
Windex or a window cleaner. The frequency of cleaning will be governed by how many hours the  
CAD Xciter is operated and by the cleanliness of the operating environment.  
FACTORY SERVICE  
Careful consideration has been given to the design of your CAD Xciter to keep maintenance  
problems to a minimum. Any problems or requests for service should be referred to our  
Customer Service Department at 919-355-0010. DO NOT return the CAD Xciter to the factory  
without a Return Authorization number (RA) from the Customer Service Department.  
Cary Audio Design will assume no responsibility if the shipping company refuses to pay for  
damage due to your improper packing or lack of insurance should the unit be lost or damaged in  
shipment. Please retain and always use the original shipping carton for shipping the player.  
16  
 
SERVICE AND CARE  
NON-WARRANTY REPAIRS  
Cary Audio Design will provide repair service for its products charging on a time and expense  
basis. The standard non warranty service bench fee is $125, plus charges for parts and materials.  
This may change and is not a quote for service. Please call us at 919-355-0010 for more  
information about out of warranty service and repair fees.  
CAUTION - Never remove or insert the back panel AC plug when the unit is on or the  
ac cord is plugged into the wall.  
WARNING - Make no attempt to put the CAD Xciter in service outside of the cabinet.  
***** Contact with lethal high voltages found in the unit can be fatal!! *****  
Do not remove the top cover or bottom covers  
17  
 
UNITED STATES LIMITED WARRANTY  
Cary Audio Design warrants to the original United States purchaser for use in the United States that Cary  
Audio Design vacuum tube or solid state power amplifiers, surround sound processors or preamplifiers shall  
be free from defects in parts or workmanship for three (3) years from the date of the original purchase.  
Vacuum tubes, if any are used in the component, are offered a 90 day from purchase date exchange policy  
against defects with the exception of the CAVT 300B vacuum tube which has a (1) one year from purchase  
date exchange policy. Any digital drive design, whether a Cary Audio Design CD or SACD player or a Cary  
Cinema DVD player, has a limited one year parts and labor warranty against defects in manufacture. This is  
a limited warrant, for the original purchaser only and does not transfer to any subsequent owner.  
During the limited warranty period, Cary Audio Design or an authorized Cary Audio Design service facility  
will provide free of charge both parts and labor necessary to correct any defects in material or  
workmanship.  
To obtain such warranty service, the original purchaser must:  
1. Complete and send in the warranty Registration Card within 15 days of purchase.  
2. If claiming service the owner must send a fully filled in copy of the original sales receipt along with  
any unit sent in for service showing the AUTHORIZED CARY AUDIO DESIGN DEALER’S name, the  
new selling price, the buyer’s name, e-mail or phone number and address on the receipt. Blank  
receipts will NOT validate the limited warranty for service.  
3. Notify Cary Audio Design as soon as possible after the discovery of a possible defect and submit  
the following information to determine eligibility for warranty:  
(a) The model number and serial number;  
(b) A fully filled in copy of the original sales receipt showing the original selling price, purchasers  
name and address filled in by an AUTHORIZED CARY AUDIO DESIGN DEALER with the original  
date of purchase shown on the form;  
(c) a detailed description of the problem.  
4. Deliver the product to Cary Audio Design or the nearest authorized service facility or ship with all  
freight and insurance charges prepaid, in its original packing container or equivalent, to Cary  
Audio.  
Correct maintenance, repair and use are important to obtain performance from this product. Therefore,  
please carefully read the Operating Manual. This warranty does not apply to any defect that Cary Audio  
Design in its sole discretion determines is due to:  
1. Improper maintenance or repair, including the installation of parts or accessories that do not  
conform to the quality and the specifications of the original parts.  
2. Misuse, abuse, neglect or improper installation.  
3. Accidental or incidental damage.  
WARRANTY DISCLAIMER  
Except for the express warranties stated herein, Cary Audio Design disclaims all other warranties including,  
without limitation, all implied warranties of merchantability and fitness for a particular purpose. The  
foregoing constitutes Cary Audio Design’s entire obligation with respect to this product, and the original  
purchaser and any user or owner shall have no other claim for incidental or consequential damages. Some  
states do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation and exclusion may not apply to you. This warranty gives legal rights and you may also have other  
rights, which vary from state to state.  
EXCLUSIVE REMEDY  
Notwithstanding the foregoing, the purchaser’s exclusive remedy for any breach of warranty, express or  
implied, is limited to the repair or replacement of the defective unit or the refund of the purchase price, at  
the option of Cary Audio Design. Under no circumstances is Cary Audio Design liable for incidental or  
consequential damages. Any implied warranties imposed by law terminate one (1) year from the date of  
purchase.  
INTERNATIONAL PURCHASERS (Export markets)  
Cary Audio Design warrants its merchandise to purchasers within the United States exclusively for use within  
the United States of America. It provides no other warranties, expressed or implied. If you are living  
outside the USA, please consult with your local dealer or distributor to determine the details of your local  
warranty.  
18  
 
CARY AUDIO DESIGN  
1020 Goodworth Drive, Apex, NC 27539  
phone 919-355-0010  
fax 919-355-0013  
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
 

Blackberry Cell Phone SWD 1000192 0414013325 001 User Manual
Black Decker Chipper 8501 Type 2 User Manual
Black Decker Paper Shredder CC2000 CC2001 User Manual
Blanco Indoor Furnishings 157 122 User Manual
Bryant Heat Pump 280ANV User Manual
Carrier Range 48EZ A User Manual
Casio Calculator fx 570ES PLUS User Manual
Casio Guitar DG 20 User Manual
Casio Watch HS 30W User Manual
Chamberlain Garage Door Opener WD822KD 1 2 HP User Manual